Gypsum board, commonly known as drywall, is a highly popular material used in interior partitioning for residential and commercial properties. Its affordability, fire resistance, and ease of installation make it the go-to solution for creating non-load-bearing walls. In this detailed blog, we’ll walk you through everything you need to know about installing gypsum board partitions — from planning to finishing.
Why Choose Gypsum Board Partitions?
Gypsum board offers several advantages:
- Lightweight construction
- Cost-effective
- Easy to install and repair
- Good sound insulation
- Fire-resistant
- Smooth finish for painting or wallpaper
Whether you’re remodeling an office, dividing a large room, or creating temporary spaces, gypsum board partitions offer versatility and efficiency.
Materials and Tools Required
Before you begin the installation process, gather the following materials and tools:
Materials:
- Gypsum boards (12.5mm standard for walls)
- Metal studs and tracks (U-channel and C-channel)
- Drywall screws
- Joint compound
- Joint tape or paper tape
- Corner beads (if needed)
- Insulation (optional for soundproofing)
- Primer and paint or wall finish
Tools:
- Tape measure
- Spirit level or laser level
- Drill/screwdriver
- Utility knife
- Drywall saw
- T-square
- Joint knife/trowel
- Sandpaper or sanding sponge
- Safety gear (gloves, goggles, mask)
Step-by-Step Guide: How to Install Gypsum Board Partitions
Step 1: Plan the Partition Layout
Start by measuring the area where the partition wall will be installed. Mark the wall and floor using a pencil or chalk line to determine where the tracks will go. Use a laser level or spirit level to ensure vertical and horizontal accuracy.
Tip: Take into account any electrical wiring, plumbing, or doors that will be needed in the partition.
Step 2: Install the Track (Floor and Ceiling Channels)
- Secure the U-shaped floor track to the floor using appropriate fasteners (concrete screws or anchors).
- Repeat the same with the ceiling track, ensuring it’s aligned with the floor track using a plumb line.
Step 3: Fix the Vertical Studs
- Insert the C-channel studs into the tracks, spaced typically 24 inches (600 mm) apart.
- Ensure all studs are plumb and secure them using screws through the track.
- Additional vertical support may be needed around door frames or for heavy fixtures.
Step 4: Install Electrical and Plumbing (if needed)
- Before fixing the gypsum boards, install all internal wiring or plumbing.
- Drill holes through studs to run wires or pipes.
- Use protective grommets to avoid cutting cables on metal edges.
Step 5: Fix the First Layer of Gypsum Boards
- Measure and cut the gypsum boards to fit the height of the wall.
- Use drywall screws to attach the board to the metal studs, placing screws every 12 inches (300 mm).
- Leave a 5-10mm gap at the floor to prevent moisture absorption.
Pro Tip: Stagger vertical joints between two sides to avoid alignment and increase structural integrity.
Step 6: Apply Joint Tape and Compound
- Use joint tape to cover seams between gypsum boards.
- Apply the joint compound using a joint knife. Smooth it over the tape and screw holes.
- Allow it to dry for 24 hours, then apply additional layers as needed (typically 2–3 coats).
- Sand it smooth once completely dry.
Step 7: Install Finishing Touches
- Install corner beads for clean and protected edges.
- Apply primer and then paint or apply wallpaper.
- You can also add skirting boards or trims as needed.
Step 8: Optional Soundproofing or Fire-Rating Upgrades
- For enhanced performance, add mineral wool or fiberglass insulation between the studs.
- Use fire-rated gypsum boards if required by building regulations.
Tips for a Smooth Gypsum Partition Installation
- Always double-check measurements before cutting.
- Use sharp tools for cleaner edges.
- Wear safety equipment when cutting or sanding boards.
- Store gypsum boards flat in a dry place before use.
- Avoid using gypsum board in areas with high moisture like bathrooms (unless using moisture-resistant types).
Common Mistakes to Avoid
| Mistake | Why It’s a Problem |
| Not checking level or plumb | Can result in crooked walls |
| Overdriving screws | Damages board and weakens hold |
| Not staggering joints | Reduces strength and may crack over time |
| Skipping primer | Paint finish may be uneven or peel |
Cost of Installing Gypsum Partition (Rough Estimate)
| Item | Approx. Cost |
| Gypsum boards (12.5 mm) | AED 18 – 30 per sheet |
| Metal Studs/Tracks | AED 8 – 15 per meter |
| Joint Tape, Screws, Compound | AED 70 – 120 (per 10 sq. meters) |
| Labor (Installation & Finish) | AED 15 – 30 per sq. foot |
Note: Costs vary based on brand, location, and design complexity.
FAQs
Conclusion
Installing a gypsum board partition is a practical way to divide space without the cost and mess of traditional masonry. With the right materials and steps, you can transform your room efficiently and affordably. Whether it’s for office use, home renovation, or temporary arrangements, gypsum partitions offer a fast, reliable, and customizable solution.
